U301 Automatic Nozzle

U301 Automatic Nozzle

U301 series automatic nozzles are designed with today's customer in mind. Small, trim, light weight, easy and convenient to operate, the is a rugged performer that offers long life and reliable service.

Materials:

Body: Aluminum

seals: Buna-N

Main stem seals: Viton Cased Oil Seal / Graphite with Teflon

Main stem: Stainless steel

Color of insulator :

Red Green Blue Yellow Black

Features :

U301-B/D/F Flow rate: 0-60 L/m (15/16")

U301-A/C/E Flow rate: 0-45 L/m (13/16")

Working Pressure: 0.18Mpa

U301 Automatic Nozzles-for diesel, kerosene and all kinds of gasonline service.

Easily replaced spout- simply remove the screw.

Spout kits are available from HONGYANG.

Low profile aluminum body- light weight, easier to handle, provides an attractive, image enhancing appearance.

Hold-open rack is available for full service applications.

The one hand control means easy setting to flow rate for customer's convenience.

Full hand insulator- protects both nozzle and vehicle, and insulates users' hands.

Selective splash guard.

100% Factory Tested.

Available Colors- color chart on inside back cover

Replacement Parts:

Key Description

1 Spout 13/16''

2 Spout 15/16''

3 Full hand insulator

4 Lever

5 Lever assembly

6 Diaphragm assembly

7 Main valve assembly

Package:

Net Weight Cross Weight Dimension

18.75kg/case of 15

12.25kg/case of 10 22kg/case of 15

15kg/case of 10 55x34x42.5cm/case of 15

37.5x34x43cm/case of 10

Important:

The products should be used in compliance with applicable country, province and local Laws and regulations. Products selection should be based on physical Specifications and limitations and compatibility with the environmentand materials to be handled. HONGYANG makes no warranty of fitness for a particular use. All illustrations and Specifications in this literature are based on the latest products information available at the time of publication,HONGYANG reserves the right to make changes at any time in price, materials. Specifications and models and to discontinue models without notice or obligation.

is illustrated in Diagram 5-13 and 5-14. It consists of controller, explosion-proof motor and co-axis vane pump. The inlet height of submersible pump is 150~250mmm from tank bottom. The motor lead of submersible pump is installed in capacitor box of upper controller. Exterior power supply is connected into junction box of lower controller. After carefully inspection submersible pump and guiding pipe are mounted into 4’�supporting pipe through lower controller, upper and lower part of controller are connected with screws in tank. Diagram 5-12: D421 Junction box wiring 2. Submersible pump wring The wiring of submersible pump is finished in controller, power supply and grounding line integrated in junction box that is sealed by rubber gasket. Connect the two black lines of power supply and controller, grounding line being fixed in junction box. The motor lead, black, brown and blue, respectively, are connected into capacitor box and sealed with rubber gasket. To connect the black lead of motor with the black in controller; brown with one of pins of capacitor, blue lead with the other terminal of capacitor after connecting with another black lead. Diagram 5-13: Installation of controller Diagram 5-14: Controller After connection scrutinize electric wiring and switch on power supply to refuel, inspecting the working state of submersible pump. 3. Fuel dispenser debugging 3.1 It is absolutely prohibited to debug fuel dispenser using water rather than oil or fuel. Debugging procedure of fuel dispenser A universal inspection should be conducted before first debugging of fuel dispenser, eliminating various elements that affect operation, lead connection in particular. Computer display fuel dispenser screen and presetting display should be carefully examined as switching on power, lighter in electric box also being check. Starting up suction pump and open nozzle, carefully examine all connection and sealed jointer face in case of leakage and penetration. Confirming each nozzle is fuel dispenser corresponded to its produ fuel dispenser

some of the data from a received message is not acceptable the complete message will be refused　　 (MS_ACK = 5) and the ACKNOWLEDGE-message will include the following detailed　　 information. Please note that all valid writes to Data_Id s (i.e. with a Data_ACK of 0) must be　　 applied to the data base.　　 bin8 1 to 255 Data Identifier　　 Data_Id　　 - the identifier for the first application data　　 element which was received　　 bin8 0 to 7 Data Acknowledge Status　　 Data_ACK　　 - the data acknowledge status byte for the　　 first application data element (details see at　　 2　　 the end of this table )　　 bin8 1 to 255 Data Identifier　　 Data_Id　　 - the identifier for the second application　　 data element which was received　　October 2002 IFSF - STANDARD FORECOURT PROTOCOL FP2_1.83　　 COMMUNICATION SPECIFICATION　　 Page: 21　　 bin8 0 to 7 Data Acknowledge Status　　 Data_ACK　　 fuel dispenser - the data acknowledge status byte for the　　 second application data element (details see　　 fuel dispenser fuel dispenser

Why hospitals must be allowed to fail Listening to the internet Past issues regional covers Higher education Organs to order GLOBAL AGENDA Remember Detroit Attack of the Eurogoogle POLITICS THIS WEEK The internet Keep it simple March of the robolawyers BUSINESS THIS WEEK China OPINION Dancing with Google s spiders How the other 800m live Leaders Flight of fancy? Letters Letters Bright sparks WORLD On America and India, Holocaust denial, Nelson United States Television s next big shift Mandela, Hugo Chávez, Russian alcoholism, leisure The Americas Asia fuel dispenser What the nose knows Middle East & Africa Europe Wi-Pie in the sky? Britain fuel dispenser Special fuel dispenser